(2) strengthening the shading measures inside and outside the window on the premise of meeting the design requirements of the building, adding external sunshade panels, awnings and appropriately increasing the length of the southward balcony can play a certain shading effect. Heat-reflecting fabric curtains coated with metal film are arranged on the inside of the window, which has a decorative effect on the front, forming a less mobile space layer about 50mm thick between the glass and the curtains. In this way, a good effect of thermal reflection and thermal insulation can be achieved, but the direct lighting is poor and should be made into a movable type. In addition, installing blinds with certain thermal reflection on the inside of the window can also obtain a certain thermal insulation effect.

First, the applicable extension width is 3, which uses a mechanical device and a crank arm device system. Under the action of spring, it can also be used for ceiling installation, light steel keel and other hard wall installation, brick wall motor control, the following is the awning fabric introduction. 00 meters, manual crank control through different transmission systems. The whole crank arm group is realized by an arm block, which can be adjusted in parallel with any precision of ~ 70 degrees. The characteristic of the 00-meter, half-box curved arm awning is that the sunshade fabric can be incorporated into the hood. Bolts and screws are made of high-quality stainless steel, applicable length is 6, can be applied to concrete, produce telescopic tension, infrared remote control and wind and rain sensor control, the structural frame adopts degree space aluminum. Wood. The common glass with good shading performance is endothermic glass, heat reflection glass, low radiation glass.

Sunshade, also known as sunshade, its function is to further prevent sunlight from coming into the car and reduce the temperature of the air in the car; at the same time, it can also protect the privacy of car owners under specific circumstances. The sunshade panels on the market range from a few yuan to dozens of yuan, and the materials are generally made of chemical fiber woven products and all-plastic films.

These parts are mainly produced by supporting manufacturers. Interior design includes dashboard, steering wheel, seat, seat belt, airbag, carpet, sidewall interior decoration, sunshade panel, handrail, car rearview mirror and so on. Exterior design includes front and rear bumper, glass, door anti-collision decoration strip, intake grille, luggage rack, skylight, rearview mirror, door structure and accessories and sealing strip.

Air-conditioned buildings rely on refrigerators to move the indoor heat load to the outside in summer. Obviously, if the indoor heat load is reduced, the running time of the refrigerator will be reduced, and the energy consumption of the cooling tower system will be reduced. The indoor heat load comes from two aspects, one is the heat exchange caused by the indoor and outdoor temperature difference, and the other is the heat load caused by indoor lighting and equipment. Therefore, sunshade, airtight, thermal insulation and other methods can be used to reduce indoor heat load and achieve energy saving. 1, reduce indoor heat load (1) sunshade to reduce direct sunlight radiation roof, wall, window and through the window to enter the room, you can use eaves, sunshade panels (awnings), coated glass, etc.; reduce the heat radiation of the external walls and roofs, you can use light-colored exterior wall finishes to set the insulation layer on the outside of the external walls and roofs, or overhead roofs.

Types include fuel tank, bumper, sunshade seat, door handle, steering wheel, dashboard and so on. Today, abs recycled plastics in the molding processing of plastic products also have a small number of failures, so that its use is bound, the mechanical strength of general plastics may as well be metal. The shrinkage of plastic is higher during molding. The sensitivity of plastic to temperature is much greater than that of metal or other non-metallic data, and the temperature boundary of plastic is much narrower than that of other data. If the plastic is loaded for a long time, even if the temperature is not high, its shape will have “creep”. The gradual plastic activity of plastic parts is unmalleable, resulting in the loss of dimensional accuracy of plastic parts.

The interior design also gives more fashion sense, although the instrument sunshade is still straight, the dashboard also retains the traditional circular mechanical type, with additional liquid crystal display in the middle; the central console and sub-dashboard adopt a fused layout, the size of the central control screen is about 10.2in, you can turn it off by touching the button on the door handle, and the four-seat rear console is disconnected from the front.